DriverZone.com: The place to find device driver updates.
Drivers
YAMAHA* AUDIO HARDWARE DEVICE DRIVERS FOR USE WITH OS/2*
--------------------
1.0 REVISION HISTORY
--------------------
July 23, 1996: Version 1.0
January 20, 1997: Version 3.02
March 21, 1997:Version 3.03
April 23, 1997:Version 3.04
----------------
2.0 INTRODUCTION
----------------
This file contains last-minute updates. Please read this file before
proceeding with the installation.
Supported OS and Hardware:
OS : OS2 Warp* Version 3 and Version 4
Hardware: OPL3-SA, OPL3-SA2, OPL3-SA3, OPL4-ML(Hardware Wavetable)
-----------------
3.0 Preparations
-----------------
1. This driver uses the multimedia application installer, so you must
first add multimedia software support (MMPM/2) to your OS/2 system.
2. Prepare sufficient free space for the driver installation in your
hard disk. Including the work area required for installation,
approximately 300 Kbytes will be necessary. However this does not
include the area used by the OS/2 system (swap area).
We recommend that you allow plenty of space.
3. If you want to delete the previous version of the driver, you must
first re-install multimedia software support (MMPM/2) (i.e., delete
the functionality and then add it once again).
-----------------------------
4.0 INSTALLATION INSTRUCTIONS
-----------------------------
Installing the Yamaha Device Driver for OS/2 Warp Version 3:
1) OS/2 will autodetect the Yamaha device as a Sound Blaster* Pro.
Do NOT install this device and remove it from the setup. The
Yamaha driver will be installed as part of the Multimedia
Application Install.
2) When installing OS/2 be sure to install the Multimedia Applications.
3) Be sure that your BIOS settings are set to NOT use a PnP OS if
using Warp 3.0.
4) Open the Multimedia Folder located on the Desktop.
5) Within the Multimedia Folder open the Multimedia Application
Install Icon.
6) Insert the Driver Diskette and change the source drive to read from
the diskette or point to the path where the driver is located.
a) Highlight and select (double click) the DRIVER directory.
b) Highlight and select (double click) the language you wish to use.
7) Highlight and select the Yamaha OPL3-SA Series Driver and then
click Install.
8) OS/2 will then prompt you that the CONFIG.SYS will be changed,
select YES.
9) Enter 1 for the number of Yamaha OPL3-SA Series Audio devices
and click OK.
10) The system will display the hardware configuration settings. Do
not modify these settings unless you are an experienced user.
Click OK.
TYPICAL VALUES FOR THE OPL3-SA ARE:
Interrupt Level: IRQ 7
WSS DMA Channel: 0, 1
WSS Base I/O Port: 530h
FM Synthesizer Base I/O Port: 388h
MPU401 Base I/O Port: Disable
MPU401 Interrupt Level: IRQ5(SA Only)
Control Register Base I/O Port: OPL3-SA
SoundBlaster Register Base I/O Port: Enable(I/O:220h)
Game Port Supporting: Enable(I/O:201h)
Game Port Supporting(Joystick Driver): Enable(I/O:201h)
TYPICAL VALUES FOR THE OPL3-SA WITH THE OPL4-ML ARE:
Interrupt Level: IRQ 7
WSS DMA Channel: 0, 1
WSS Base I/O Port: 530h
FM Synthesizer Base I/O Port: 388h
MPU401 Base I/O Port: 330h
MPU401 Interrupt Level: IRQ5(SA Only)
Control Register Base I/O Port: OPL3-SA
SoundBlaster Register Base I/O Port: Enable(I/O:220h)
Game Port Supporting: Enable(I/O:201h)
Game Port Supporting(Joystick Driver): Enable(I/O:201h)
TYPICAL VALUES FOR THE OPL3-SA2 OR OPL3-SA3 ARE:
Interrupt Level: IRQ 7
WSS DMA Channel: 0, 1
WSS base I/O Port: 530h
FM Synthesizer Base I/O Port: 388h
MPU401 Base I/O Port: Disable
MPU401 Interrupt Level: SA2/SA3
Control Register Base I/O Port: 390h(SA2 or SA3)
SoundBlaster Register Base I/O Port: Enable(I/O:220h)
Game Port Supporting: Enable(I/O:201h)
Game Port Supporting(Joystick Driver): Enable(I/O:201h)
TYPICAL VALUES FOR THE OPL3-SA2 OR OPL3-SA3 WITH THE OPL4-ML ARE:
Interrupt Level: IRQ 7
WSS DMA Channel: 0, 1
WSS base I/O Port: 530h
FM Synthesizer Base I/O Port: 388h
MPU401 Base I/O Port: 330h
MPU401 Interrupt Level: SA2/SA3
Control Register Base I/O Port: 390h(SA2 or SA3)
SoundBlaster Register Base I/O Port: Enable(I/O:220h)
Game Port Supporting: Enable(I/O:201h)
Game Port Supporting(Joystick Driver): Enable(I/O:201h)
NOTE: to enable support for OPL4-ML (Hardware wavetable) or
external MIDI devices, set MPU401 Support to enabled. If
no Hardware Wavetable devices or External MIDI devices are present
set the MPU401 Base I/O: to disabled default settings.
11) OS/2 will then prompt that the changes have taken place.
12) Reboot if necessary.
Installing the Yamaha Device Driver for OS/2 Warp Version 4:
1) When installing OS/2 be sure to install the Multimedia Applications.
2) OS/2 will autodetect the Yamaha device as a Sound Blaster Pro.
Do NOT install this device and remove it from the setup. The
Yamaha driver will be installed as part of the Multimedia
Application Install.
3) Once OS/2 is loaded. Double click on the OS/2 System icon on the
Desktop.
4) Double click the System Setup Icon.
5) Double click the Install/Remove Icon.
6) Double click the Multimedia Application Install Icon.
7) Insert the Driver Diskette and change the source drive to read from
the diskette or point to the path where the driver is located.
a) Highlight and select (double click) the DRIVER directory.
b) Highlight and select (double click) the language you wish to use.
8) Highlight and select the Yamaha OPL3-SA Series Driver and then
click Install.
9) OS/2 will then prompt you that the CONFIG.SYS will be changed,
select YES.
10) Enter the number of Yamaha OPL3-SA Audio devices to be 1 and click
OK.
11) The system will display the hardware configuration settings. Do
not modify these settings unless you are an experienced user.
Click OK.
TYPICAL VALUSES FOR THE OPL3-SA ARE:
Interrupt Level: IRQ 7
WSS DMA Channel: 0, 1
WSS Base I/O Port: 530h
FM Synthesizer Base I/O Port: 388h
MPU401 Base I/O Port: Disable
MPU401 Interrupt Level: IRQ5(SA Only)
Control Register Base I/O Port: OPL3-SA
SoundBlaster Register Base I/O Port: Enable(I/O:220h)
Game Port Supporting: Enable(I/O:201h)
Game Port Supporting(Joystick Driver): Enable(I/O:201h)
TYICAL VALUES FOR THE OPL3-SA WITH THE OPL4-ML INSTALLED ARE:
Interrupt Level: IRQ 7
WSS DMA Channel: 0, 1
WSS Base I/O Port: 530h
FM Synthesizer Base I/O Port: 388h
MPU401 Base I/O Port: 330h
MPU401 Interrupt Level: IRQ5(SA Only)
Control Register Base I/O Port: OPL3-SA
SoundBlaster Register Base I/O Port: Enable(I/O:220h)
Game Port Supporting: Enable(I/O:201h)
Game Port Supporting(Joystick Driver): Enable(I/O:201h)
TYPICAL VALUES FOR THE OPL3-SA2 OR OPL3-SA3 ARE:
Interrupt Level: IRQ 7
WSS DMA Channel: 0, 1
WSS base I/O Port: 530h
FM Synthesizer Base I/O Port: 388h
MPU401 Base I/O Port: Disable
MPU401 Interrupt Level: SA2/SA3
Control Register Base I/O Port: 390h(SA2 or SA3)
SoundBlaster Register Base I/O Port: Enable(I/O:220h)
Game Port Supporting: Enable(I/O:201h)
Game Port Supporting(Joystick Driver): Enable(I/O:201h)
TYPICAL VALUES FOR THE OPL3-SA2 OR OPL3-SA3 WITH THE OPL4-ML ARE:
Interrupt Level: IRQ 7
WSS DMA Channel: 0, 1
WSS base I/O Port: 530h
FM Synthesizer Base I/O Port: 388h
MPU401 Base I/O Port: 330h
MPU401 Interrupt Level: SA2/SA3
Control Register Base I/O Port: 390h(SA2 or SA3)
SoundBlaster Register Base I/O Port: Enable(I/O:220h)
Game Port Supporting: Enable(I/O:201h)
Game Port Supporting(Joystick Driver): Enable(I/O:201h)
NOTE: to enable support for OPL4-ML (Hardware wavetable) or
External MIDI devices MPU401 Support must be set to enabled. If
no Hardware Wavetable devices or External MIDI devices are present
please select the MPU401 Base I/O: disabled default settings.
12) OS/2 will then prompt that the changes have taken place.
13) Reboot if necessary.
-------------------------------
5.0 UNINSTALLATION INSTRUCTIONS
-------------------------------
To un-install the Yamaha Device Driver, the following
lines must be removed from the respective files.
CONFIG.SYS
Device=C:\MMOS2\OPL3SA.SYS /I:11 /D:01 /W:530 /F:388 /M:0 /A:0 /C:390 /S:220 /N:OPL3S1$ /J:1,201
Device=C:\MMOS2\OPL3VDD.SYS OPL3S1$
Device=C:\MMOS\GAMEDD.SYS /J:I,201
Device=C:\MMOS\GAMEVDD.SYS
MMPM2.INI file
[Drivers]
Waveaudio = YMSWAVEOPL3SA01
Sequencer = YMSSEQOPL3SA01
Ampmix = YMSAMPMIXOPL3SA01
[YMSWAVEOPL3SA01]
[YMSWAVEOPL3SA01-PLAY]
[YMSWAVEOPL3SA01-RECORD]
[YMSSEQOPL3SA01]
[YMSSEQOPL3SA01-PLAY]
[YMSAMPMIXOPL3SA01]
-----------
6.0 OPTIONS
-----------
When installation successfully completes, the following lines are added
to CONFIG.SYS:
DEVICE=[MMOS2 dir]\OPL3SA.SYS (*)
DEVICE=[MMOS2 dir]\GAMEDD.SYS (*)
DEVICE=[MMOS2 DIR]\OPL3VDD.SYS (*)
DEVICE=[MMOS2 DIR]\GAMEVDD.SYS
where (*) is:
/I:xx:5,7,9,10,11 'Interrupt for Windows Sound System
/D:xx,yy:0,1,3 'DMA channel for Windows Sound System
/W:xxx:530,604,E80,F40 'Base I/O address for Windows Sound System
/F:xxx:388,398,3A8,3B8 'Base I/O for OPL3
/M:xxx:330,320,310,300 'Base I/O address for MPU401
/C:xxx:F86,390,620,910,A10 'Base I/O address for control registers
/N:xxx 'Name of the device driver
/A:xx:5,7,9,10 (/A:1,2,3,4 (Ymersion MODE for OPL3-SA3B))
'Interrupt for MPU401 (0 for SA2/SA3)
'Also in the case of the OPL3-SA3B, you can set the YMERSION mode
by selecting one of the following values for this option.
1: Desktop,2: Notebook(1),3: Notebook(2),4: HiFi
For values other than the above, Normal mode will be selected.
/S:xxx:0 disable,220,240,260 'Base I/O address for Sound Blaster
/J:x,yyy x:0(Disable), 1(Enable) 'control for Joystick
yyy: 201,20A,20E
---------------------
7.0 SUPPORTED FEATURES
----------------------
1) Supported devices
Wave_Out, Wave_In
2) Supported sampling rates
11.025kHz,22.05kHz,44.1kHz
3) Formats
Monaural and Stereo, 8bit unsigned PCM and 16bit signed PCM
4) MIDI_Out
OPL3 & MPU401 for external wavetable synthesizer
5) Mixer
This driver supports the playback volume for Master, Wave,
Synthesizer(for internal FM or external synthesizer), CD audio,
Mic._In, Line_In. And the recording volume for CD audio,
Line_In, Mic_In and loopback are supported.
6) Game port driver is supported.
------------------------------
8.0 LIMITATIONS
------------------------------
1) Resources. Regarding the resource that this driver uses (ex. I/O
address, IRQ and DMA channel), there are constraints resulting from
the hardware configuration.
2) MIDI playback device assignment. If MPU401 is enabled, FM synth
playback will not work.
-------------------------
9.0 COPYRIGHT/TRADEMARKS
-------------------------
*Other brands and trademarks are the property of their respective owners.
| Filename | Size | Readme | O.S. | Description | |
 |
31v2329.exe | 1751KB | 31v2329.htm | YAMAHA OPL3-Sax drivers update for Windows 3.1 These are reference drivers, if possible get the drivers from you OEM vendor, if you are unsure who made you card, you can look them up using the FCC Search |
|
|
95v1026.exe | 5578KB | 95v1026.htm | Yamaha Windows 95 /98 drivers for the YMF724 / YMF740, also called DS-XG and the WAVEFORCE192 Sound card only SEE THE README BEFORE DOWNLOADING !!! |
|
|
95v2343.exe | 1948KB | 95v2343.htm | Yamaha OPL3-SAx Driver Installation for Win95/98. These are reference drivers, if possible get the drivers from you OEM vendor, if you are unsure who made you card, you can look them up using the FCC Search |
|
|
dsxgwin2k.exe | 4750KB | Yamaha Windows 2000 drivers for the Waveforce DS-XG sound cards | ||
|
ntv2311.exe | 138KB | ntv2311.htm | Yamaha OPL3-SAx Driver Installation for WinNT These are reference drivers, if possible get the drivers from you OEM vendor, if you are unsure who made you card, you can look them up using the FCC Search |
|
|
ntv6017.exe | 3387KB | ntv6017.htm | Yamaha Windows NT driver for YMF724 and YMF740, also called DS-XG, which was soldered down on the motherboard. | |
|
os2v304.exe | 1948KB | os2v304.htm | Yamaha drivers for OS/2 supporting these models: OPL3-SA, OPL3-SA2, OPL3-SA3, OPL4-ML(Hardware Wavetable) | |
 |
setupdrv.zip | 4232KB | Yamaha WaveForce 192 XG drivers for windows 95/98 | ||
|
winnt.zip | 2744KB | Yamaha WaveForce 192 XG drivers for Windows NT | ||
|
yamaha_dsxg_driver.exe | 5955KB | Yamaha Windows 95 /98 DS-1x Drivers for YMF724, YMF740, YMF744, YMF754 These are reference drivers, if possible get the drivers from you OEM vendor, if you are unsure who made you card, you can look them up using the FCC Search |
||
|
yamaha_dsxg_nt_driver.exe | 5608KB | Yamaha Windows NT 4.0 DS-1x Drivers for YMF724, YMF740, YMF744, YMF754 These are reference drivers, if possible get the drivers from you OEM vendor, if you are unsure who made you card, you can look them up using the FCC Search |
style="display:inline-block;width:336px;height:280px"
data-ad-client="ca-pub-5193782351433030"
data-ad-slot="2063583586">