Drivers

***** How to install the device driver under Windows environment *****

To operate TEAC CD-ROM,the device driver (TEAC_CDI.SYS) has to be installed
from INSTALLATION DISK came along with CD-ROM.
Please follow the instruction below.

1. Start up the Windows.

2. Insert INSTALLATION DISK in Floppy Disk Drive.

3. Open "File" menu and select "Run".

4. Type "A:\SETUP" and click "OK".(If Floppy Disk Drive is "A:")

5. Install program starts and follow the screen.

6. When the installation is completed successfully,the program will ask you
to re-boot the system.During the boot process the following screen will be
appeared.

MSCDEX Version 2.23
Copyright (C) Microsoft Corp. 1986-1993. All rights reserved.

Drive D: = Driver TEAC-CDI unit 0

* 'D:' ... Drive letter assigned to CD-ROM Drive

This message means that TEAC CD-ROM drive is now activated.

* Now the installation of TEAC CD-ROMdrive is completed.

***** How to install the device driver under DOS environment *****

If you want to install it under DOS, please follow the instruction below.

1. Please copy the following file located in the root directory of INSTALLATION
DISK to your Hard disk drive.
TEAC_CDI.SYS
(Example) COPY A:\TEAC_CDI.SYS C:\TEAC_CDI.SYS
(A:FLOPPY DISK ,C:HARD DISK DRIVE)

2. Please add the following line in your Config.sys file by using Text
Editor (EDIT.COM for MS-DOS or E.EXE for PC-DOS etc). This statement can be
added in any line.
DEVICE=C:\TEAC_CDI.SYS /D:TEAC-CDI
* "C" is drive letter which contains TEAC_CDI.SYS file

3. Please add the following line in your Autoexec.bat file by using Text
Editor (EDIT.COM for MS-DOS or E.EXE for PC-DOS). This statement can be
added in any line.
C:\MSCDEX.EXE /D:TEAC-CDI
* "C" is drive letter which contains DOS

4. Remove the setup floppy disk from the drive after editing both Config.sys
and Autoexec.bat then reboot your computer.

5. The following should be displayed on the screen during boot-up

MSCDEX Version 2.23
Copyright (C) Microsoft Corp. 1986-1993. All rights reserved.

Drive D: = Driver TEAC-CDI unit 0

* 'D:' ... Drive letter assigned to CD-ROM Drive

This message means that TEAC CD-ROM drive is now activated.

* Now the installation of TEAC CD-ROMdrive is completed.

***** TEAC CD-ROM DRIVE Trouble Shooting Tips *****

------------------------------------------------------------------------------
Q1: System will not boot when CD-ROM drive is daisy-chained with
hard disk drive.
------------------------------------------------------------------------------
A1: Be sure your hard disk drive jumper is set to MASTER and CD-ROM's to SLAVE.
Please refer to the installation manual for CD-ROM jumper setting and ask
hard drive manufacturer for MASTER jumper setting.
Note: There may be a case where CD-ROM can not be daisy-chained with
Conner hard drive (Conner mode).
A2: Check if the I/F cable is connected reversely.

------------------------------------------------------------------------------
Q2: System hangs without displaying anything when the device driver is loaded
during Boot-up.
------------------------------------------------------------------------------
A1:There is a possibility that TEAC device driver is having a conflict with
others. Please check the position of the device driver statement or remark
driver which may be having a conflict with.
A2:In case that TEAC CD-ROM drive is connected with non TEAC CD-ROM drive in
the same system.
Please re-install the TEAC CD-ROM address by going through 'SELECT I/O PORT'.

------------------------------------------------------------------------------
Q3: "Not Install Device Driver" message is displayed during loading the device
driver.
------------------------------------------------------------------------------
A1:Please make sure that Power cable and I/F cable are properly connected.
A2:Please make sure that there is no conflict with IDE card address (primary,
secondary, tertiary etc.) and/or interrupt.
A3:In case that CD-ROM drive is daisy-chained with hard disk drive, please
make sure that hard disk drive jumper is set to MASTER and CD-ROM's to SLAVE.
Please refer to the installation manual for CD-ROM jumper setting and ask
hard drive manufacturer for MASTER jumper setting.
A4:In case that your IDE I/O address is set to Tertiary/Quaternary, please
re-install the TEAC CD-ROM Software to change the address by selecting
'SELECT I/O PORT'.
A5:There will be the case where TEAC CD-ROM drive will not work with IDE
Controller card with Cache.

------------------------------------------------------------------------------
Q4: CD-ROM drive will not be recognized by the system when MSCDEX.EXE
(or CORELCDX.COM) is loaded.
------------------------------------------------------------------------------
A: Drive names specified in Config.sys and Autoexec.bat may not be matching.
Please make sure that each statement has "/D:TEAC-CDI"

------------------------------------------------------------------------------
Q5: System does not recognize the CD-ROM drive with error message "Not enough
drive letters".
------------------------------------------------------------------------------
A: There may be no more Drive letter available. Please add or edit "LASTDRIVE"
statement so that the last drive equals one more than your current last drive.
(Example)
Current New
A:FDD A:FDD
B:FDD B:FDD
C:HDD C:HDD
D:HDD D:HDD
E:CD-ROM -> "LASTDRIVE=E"

------------------------------------------------------------------------------
Q6: Getting the display "XMS cache not installed" when CORELCDX.COM is loaded.
------------------------------------------------------------------------------
A: Please refer to the CorelCDX's document file (CORELCDX.TXT).

------------------------------------------------------------------------------
Q7: Getting the display "CDR101: Not Ready" when CD-ROM is accessed.
------------------------------------------------------------------------------
A: Please make sure that the disk is inserted in the drive or is not placed up
side down.

------------------------------------------------------------------------------
Q8: Getting the display "CDR103: CD-ROM not High Sierra or ISO 9660 format"
when CD-ROM is accessed.
------------------------------------------------------------------------------
A: This message will be displayed when non-standard CD is accessed.
(Example) Placing Audio CD and accessing it without going into CDPLAYER.

------------------------------------------------------------------------------
Q9: CD-ROM drive is not recognized when RAM Boost is used.
------------------------------------------------------------------------------
A: Please insert the TEAC device driver statement before Ram Boost statement
in your Config.sys.

------------------------------------------------------------------------------
Q10: Do I need BIOS CMOS Setup for my IDE CD-ROM ?
------------------------------------------------------------------------------
A: No,CD-ROM is not supported by BIOS.It is different from Hard Disk Drive.
Please select "none" for BIOS Setup of CD-ROM I/O port.

------------------------------------------------------------------------------
Q11: CD-PLAYER for Windows will not work.
------------------------------------------------------------------------------
A: To operate CD-PLAYER for Windows,[MCI]CD Audio has to be installed in
Drivers in Control Panel.Please refer to Windows manual to install
[MCI]CD Audio.

------------------------------------------------------------------------------
Q12: How can I see Photo CD ?
------------------------------------------------------------------------------
A: You have to use Photo CD access software released from Kodak,Corel or
Adaptec to see Photo CD.

------------------------------------------------------------------------------
Q13: How can I see CD-I/Video CD ?
------------------------------------------------------------------------------
A: You need MPEG Playback Card (Ex.RealMagic) to play CD-I/Video CD/Karaoke CD.
You can see a directory of Video CD but not of CD-I.

------------------------------------------------------------------------------
Q14: I can't play CD-I.
------------------------------------------------------------------------------
A: There are two kinds of Disk.One is called CD-I which you have to use
CD-I player and the other is CD-I Digital Video which you can play with
CD-ROM drive and MPEG Playback Card.

------------------------------------------------------------------------------
Q15: Video CD Ver.2.0 can be played ?
------------------------------------------------------------------------------
A: It depends on your MPEG Playback Card.

------------------------------------------------------------------------------
Q16: Will CD-ROM drive work with i386 system ?
------------------------------------------------------------------------------
A: Yes,it will work with i386 but i486 or higher system is recommended to get
better performance.

------------------------------------------------------------------------------
Q17: How can I use CD-ROM under OS/2 ?
------------------------------------------------------------------------------
A: TEAC CD-ROM will work with the embedded ATAPI driver in OS/2 Warp Ver.3.0.

------------------------------------------------------------------------------
Q18: How can I get the device driver for Windows NT/95 ?
------------------------------------------------------------------------------
A: Please select embedded ATAPI driver in Windows NT/95.

==============================================================================
Technical support
==============================================================================
TEAC America Inc.
Phone 213-727-4860
BBS 213-727-7660
Fax on Demand 213-727-7629

Filename	Size	Readme	O.S.	Description
cd55ant.zip	12KB	cd55ant.htm		This is the Windows NT 3.5x BETA driver for the Teac CD-55A 4x CD-ROM.
cd55os2.zip	10KB	cd55os2.htm		This is the OS/2 2.1 and OS/2 WARP 3 drivers for the Teac CD-55A 4x CD-ROM that is attached to a Teac 8-bit I/F controller card only. Note: The file README.55A contains the I/O jumper settings for the Teac 8-bit I/F controller card.
cd55_w3x.zip	295KB			This is the DOS and Windows 3.x driver for the Teac CD-55A 4x CD-ROM that is attached to a Teac 8-bit I/F controller card only.
cd55_w95.zip	9KB	cd55_w95.htm		This is the Windows 95 driver for the Teac CD-55A 4x CD-ROM that is attached to a Teac 8-bit I/F controller card only.
cd55__95.zip	11KB	cd55__95.htm		This is the Windows 95 driver for the Teac CD-55A 4x CD-ROM that is attached to either a Teac 8-bit or 16-bit I/F controller card.
teac24x.zip	592KB	teac24x.htm		These are the DOS and Windows 3.1x/95 drivers for the Teac 24x CD-ROM.
teac56e.zip	33KB	teac56e.htm		This is the ATAPI/DOS driver for the Teac CD-56E 6x IDE CD-ROM.
teac58e.zip	475KB	teac58e.htm		This is the ATAPI/DOS driver for the Teac CD-58E 8x IDE CD-ROM.

DriverZone.com: The place to find device driver updates.